Sold by:

®

CCNP TSHOOT 6.0 INSTRUCTOR LAB MANUAL PDF - CCNP ROUTE Instructor Lab Manual. Use by instructors in the CCNP TSHOOT course as part of an This. Chemistry lab manual.

http://www.TWAcomm.com

Toll Free: (877) 892-2666

2 Slide the battery

compartment cover

completely off of

the Back-UPS ES.

Connect

Equipment

Place the Back-UPS ES to avoid:

Battery Back-up plus

Surge Protection

2

- Direct sunlight

These outlets are powered whenever the Back-UPS ES is

- Excessive heat

- Excessive humidity or contact with fluids

switched ON. During a power outage or other utility problems

(brownouts, over-voltages), these outlets will be powered for a

Connect FAX/Modem/Phone

Plug the Back-UPS ES power cord directly

limited time by the Back-UPS ES. Plug your computer, monitor,

Back-UPS ES protects a single

into a wall outlet; not a surge protector or

and one other>

Connect Computer Cable

UPS ES as shown.

The supplied cable and software provide

automatic file saving and shutdown of the

operating system in the case of a sustained

Battery Backup plus Surge Protection

power outage.

Wall Outlet

Connect the cable to the Data Port of the Back-

Surge Protection

UPS ES. Connect the other end of the cable to

the USB port on your computer. The software will

automatically find the USB Port of your

P o w e r O n

computer.

Modem/Phone/Fax

Surge Protection

Circuit

Breaker

These outlets provide full-time protection from surges even if

Computer

Cord

UPSPower

On Indicator

AC Line

the Back-UPS ES is switched OFF. Plug your printer, fax

USB Port

Building Wiring

PowerOn

machine, scanner, or other peripherals that do not need

FaultIndicator

battery power into these outlets.

Power

Switch

Status

Visual Indications

Audible Indication

Alarm Terminates

When

On Line - UPS is supplying conditioned

Power On LED - ON

None

n/a

utility power to the load

On Battery - UPS is supplying battery

Power On LED - ON

Beeping 4 times

UPS transfers back to

power to the load connected to the

(off during beep)

every 30 seconds

On Line operation, or

Battery outlets

when UPS is turned

off.

Low Battery Warning - UPS is supplying

Power On LED -

Rapid beeping (one

UPS transfers back to

battery power to the load connected to

Flashing

second intervals)

On Line operation, or

the Battery outlets and the battery is near

when UPS is turned

exhuastion

off.

Replace Battery - Battery needs to be

Power On LED -

Constant tone

UPS turned off with

checked and/or replaced, or battery is not

Flashing

the power switch.

connected

Overload Shutdown - During On Battery

Power On LED - OFF

Constant tone

UPS turned off with

operation a battery power supplied outlet

the power switch.

overload was detected.

Sleep Mode - During On Battery

Power On LED - OFF

Beeping once every

UPS transfers back to

operation the battery power has been

4 seconds

On Line operation, or

completely exhausted and the UPS is

when UPS is turned

waiting for utility power to return to

off.

normal.

Building Wiring Fault - Your building

Building Wiring Fault

None

UPS is unplugged, or

wiring presents a shock hazard that

LED (red) - ON

plugged into a

should be corrected by a licensed

properly wired outlet.

electrician.

990-9197 Revision 1 11/01 Copyright © 2001 American Power Conversion Corp.

APC, Back-UPS and PowerChute are registered trademarks of American Power Conversion Corp.

Troubleshooting

Use the table below to solve minor Back-UPS ES installation or operation problems. Consult APC Online Technical Support or call APC

Technical Support for assistance with problems that cannot be resolved using the table below:

Problem

Probable Cause

Solution

Back-UPS ES will not turn on.

Battery is disconnected and utility power is not available at

Connect the battery (see Connect Battery) and ensure power is available at the wall

the wall outlet.

outlet.

No power available at the Surge Protection

Surge Protection outlets have been overloaded.

Reduce the amount of equipment plugged into Surge Protection outlets.

outlets.

Utility power not available at the wall outlet.

Ensure that the fuse or circuit breaker for the outlet is not tripped, and that the wall

switch controlling the outlet (if any) is in the ON position.

Connected equipment loses power.

Equipment is connected to the “Surge Protection” outlets.

Ensure that the equipment you want to stay powered during a power failure is

plugged into the “Battery Backup plus Surge Protection” outlets and NOT the “Surge

Protection” outlets.

The Back-UPS ES is overloaded.

Make sure that the equipment plugged into the outlets of the unit are not overloading

the capacity of the unit. Try removing some of the equipment and see if the problem

continues.

PowerChute Personal Edition software has performed a

The Back-UPS ES is operating normally.

shutdown due to a power failure.

The Back-UPS ES has exhausted its available battery

The Back-UPS ES can only operate on battery power for a limited amount of time.

power.

The unit will eventually turn off when the available battery power has been used.

Allow the unit to recharge for 16 hours before continuing use of the unit.

Connected equipment does not accept the step-

The output waveform is designed for computers and computer-related equipment. It

approximated sine waveform the Back-UPS ES.

is not designed for use with motor-type equipment.

The Back-UPS ES may require service.

Contact APC Technical Support for further troubleshooting.

The Power On indicator is lit and the Back-

The Back-UPS ES is using battery.

The Back-UPS ES is operating normally and using battery power. Once On Battery,

UPS ES is beeping four times every 30

you should save your current work, power down your equipment, and turn the unit

seconds.

OFF. Once normal power is restored, you may turn the unit back ON and power

your equipment.

The Power On indicator flashes once per

Battery capacity is low (about 2 minutes of use remaining).

The Back-UPS ES is about to shut off due to a low battery charge condition! When

second and the Back-UPS ES beeps once

the unit beeps once every second, the battery has about 2 minutes of power

per second at the same time.

remaining. Immediately power down your computer and turn the unit OFF. When

normal power returns, the unit will recharge the battery.

Building Wiring Fault indicator is lit.

Your building wiring presents a shock hazard. Using the

Call a qualified electrician for service.

Back-UPS with this condition will void the warranty.

Inadequate runtime.

The battery is not fully charged.

Allow the unit to charge by leaving it plugged into the wall at least 16 hours.

Battery is near the end of useful life.

As a battery ages, the amount of runtime available will decrease. You can replace

the battery by ordering one at www.apc.com. Batteries also age prematurely if the

Back-UPS ES is placed near excessive heat.

Model

BE350U

BE500U

Input

Voltage

120 Vrms Nominal

Frequency

47 - 63 Hz

Brownout Transfer

96 Vrms, typical

Over-voltage Transfer

136 Vrms, typical

Output

UPS Capacity (3 outlets)

350 VA / 200 W

500 VA / 300 W

Surge Capacity (6 outlets)

12 Amps (including UPS output)

Voltage

115 Vrms + 8%

On Battery

(step-approximated sine wave)

Frequency - On Battery

50-60 Hz + 1 Hz

Transfer Time

5 ms typical, 8 ms maximum

Protection and Filter

AC Surge Protection

Full time, 375 joules

Telephone Surge Protection

Single line (2-wire)

EMI/RFI Filter

Full time

AC Input

Resettable circuit breaker

Battery

Type

Sealed, maintenance-free lead acid

Average Life

2 - 4 years depending on the number of discharge

cycles and environmental temperature

Physical

Net Weight

9.20 lb. (4.18 kg.)

13.25 lb. (6.02 kg.)

Size

3.3” (H) x 10.9” (W) x 6.9” (D)

(8.3 x 27.8 x 17.5 cm)

Operating Temperature

+32oF to 104oF (0oC to 40 oC)

Storage Temperature

o

F to 113

o

o

o

+5

F (-15 C to 45 C)

Operating Relative Humidity

0 to 95% non-condensing

Operating Elevation

0 to 10,000 ft (0 to 3,000m)

Safety/Regulatory

Safety Approvals

UL 1778 listed, cUL certified per

CSA standard C22.2 No. 107.1

EMC Compliance

FCC part 68, FCC part 15 Class B

Notice: This device complies with part 15 of

the FCC rules. Operation is subject to the

following two conditions: (1) This device may

not cause harmful interference, and (2) This

device must accept any interference received,

including interference that may cause

undesired operation.

Sold by:

http://www.TWAcomm.com

Toll Free: (877) 892-2666